CPTR: conditional probability tree based routing in opportunistic networks

In opportunistic networks due to the inconsistency of the nodes link, routing is carried out dynamically and we cannot use proactive routes. In these networks, nodes use opportunities gained based on store-carry-forward patterns to forward messages. Every node that receives a message when it encounters another node makes decision regarding the forwarding or not forwarding the node encountered. In some previous methods, the recognition of whether encounter with current node is considered as an appropriate opportunity or not has been carried out based on the comparison of the probability of carrier node and the node encountered. In these methods, if the message is delivered to the encountered node, a better opportunity would be lost. To fight with this challenge we have posed CPTR method by using conditional probability tree method through which in addition to the probability of the delivery of carrier and encountered nodes’ message delivery, the opportunities for after encounter will be involved in messages’ forwarding. Results of simulation showed that the proposed method can improve the ratio of delivery and delay of message delivery compared to other similar methods in networks with limited buffer.     

Evaluation of Microstructure and Mechanical Properties in Dissimilar Austenitic/Super Duplex Stainless Steel Joint

To study the effect of chemical composition on microstructural features and mechanical properties of dissimilar joints between super duplex and austenitic stainless steels, welding was attempted by gas tungsten arc welding process with a super duplex (ER2594) and an austenitic (ER309LMo) stainless steel filler metal. While the austenitic weld metal had vermicular delta ferrite within austenitic matrix, super duplex stainless steel was mainly comprised of allotriomorphic grain boundary and Widmanstätten side plate austenite morphologies in the ferrite matrix. Also the heat-affected zone of austenitic base metal comprised of large austenite grains with little amounts of ferrite, whereas a coarse-grained ferritic region was observed in the heat-affected zone of super duplex base metal. Although both welded joints showed acceptable mechanical properties, the hardness and impact strength of the weld metal produced using super duplex filler metal were found to be better than that obtained by austenitic filler metal.     

Open circuit voltage profiling as diagnostic tool during stack lifetime testing

A 10-cell Mk 9 stack was characterized using current/voltage mapping during automotive drive cycle testing. A minimally invasive current mapping technique was used to determine localized polarization curves which together with open circuit voltage (OCV) profile measurements provide useful information about crossover leak formation and location. Through a systematic variation of reactant gas pressures it is further possible to distinguish between electrical shorts, diffusive and convective leaks.     

Bending analysis of functionally graded annular sector plates by extended Kantorovich method

The small deflection equation for isotropic and non-homogenous thin annular sector subject to transverse loading is derived in polar coordinate. The Poisson’s ratio of the plate is assumed to be constant, but the Young’s modulus varies continuously through the radial direction according to the power-law function. A closed-form solution with fast convergence rate is obtained using the extended Kantorovich method and the classical theory of thin plates (Kirchhoff theory). The validity and accuracy of results are examined by resolving the problem using commercial finite element code ABAQUS and a good agreement between them is obtained for either deflection or stress resultants.     

Negotiation strategies considering market, time and behavior functions for resource allocation in computational grid

Providing an efficient resource allocation mechanism is a challenge to computational grid due to large-scale resource sharing and the fact that Grid Resource Owners (GROs) and Grid Resource Consumers (GRCs) may have different goals, policies, and preferences. In a real world market, various economic models exist for setting the price of grid resources, based on supply-and-demand and their value to the consumers. In this paper, we discuss the use of multiagent-based negotiation model for interaction between GROs and GRCs. For realizing this approach, we designed the Market- and Behavior-driven Negotiation Agents (MBDNAs). Negotiation strategies that adopt MBDNAs take into account the following factors: Competition, Opportunity, Deadline and Negotiator’s Trading Partner’s Previous Concession Behavior. In our experiments, we compare MBDNAs with MDAs (Market-Driven Agent), NDF (Negotiation Decision Function) and Kasbah in terms of the following metrics: total tasks complementation and budget spent. The results show that by taking the proposed negotiation model into account, MBDNAs outperform MDAs, NDF and Kasbah.     

Schiff base complex of Cu immobilized on MCM-41 as reusable catalyst for efficient oxidative coupling of thiols and oxidation of sulfides using hydrogen peroxide

Schiff base complex of copper-functionalized MCM-41 (Cu-complex@MCM-41) was synthesized and used as an efficient and novel heterogeneous catalyst for the oxidative coupling of thiols into corresponding disulfides and oxidation of sulfides to sulfoxides using hydrogen peroxide (H₂O₂) as the oxidant. An aliphatic and aromatic series of sulfides and thiols including various functional groups were successfully converted into corresponding products. The all products were obtained in good to excellent yields. The mesoporous catalyst is characterized by FT-IR spectroscopy, BET, XRD, SEM, EDS and TGA. Recovery of the catalyst is easily achieved by simple filtration and reused for several consecutive runs without significant loss of its catalytic efficiency.     

Modified guar gum: An alternative source for printing of cotton fabric with reactive dye

The alginate thickener is the thickener frequently used for reactive printing of textile. The thickener responds with reactive pigments and thus does not lead to the fabric composition becoming stiffer. In this study, we prepared oxidised natural guar gum with hydrogen peroxide, sodium hypochlorite and sodium hydroxide. All other polysaccharides comprise reactive hydroxyl units with a stronger reactivity that must be replaced if they are to be used in reactive printing. Guar derivatives were synthesised and verified using Fourier-transform infrared (FTIR) spectroscopy. Natural thickeners, synthetic guar gum derivatives, have been employed in textile printing technique. In comparison to other synthetic thickeners, modified environmental guar gum polymer has been shown to be an ecologically friendly and low-cost thickener. Cotton fabric printed with modified guar thickening with hydrogen peroxide has even stronger colour strength than fabric printed with sodium alginate thickener, which is highly favourable. Penetration properties, colour value, colour strength, colour fastness to washing, light and rubbing was compared with alginate thickener (readily available on the market). Guar gum thickeners showed enhanced features versus sodium alginate for reactive printing. Partially replaced guar gum is an appropriate option due to the colour and physical properties.     

A High Throughput Configurable SDR Detector for Multi-user MIMO Wireless Systems

Spatial division multiplexing (SDM) in MIMO technology significantly increases the spectral efficiency, and hence capacity, of a wireless communication system: it is a core component of the next generation wireless systems, e.g. WiMAX, 3GPP LTE and other OFDM-based communication schemes. Moreover, spatial division multiple access (SDMA) is one of the widely used techniques for sharing the wireless medium between different mobile devices. Sphere detection is a prominent method of simplifying the detection complexity in both SDM and SDMA systems while maintaining BER performance comparable with the optimum maximum-likelihood (ML) detection. On the other hand, with different standards supporting different system parameters, it is crucial for both base station and handset devices to be configurable and seamlessly switch between different modes without the need for separate dedicated hardware units. This challenge emphasizes the need for SDR designs that target the handset devices. In this paper, we propose the architecture and FPGA realization of a configurable sort-free sphere detector, Flex-Sphere, that supports 4, 16, 64-QAM modulations as well as a combination of 2, 3 and 4 antenna/user configuration for handsets. The detector provides a data rate of up to 857.1 Mbps that fits well within the requirements of any of the next generation wireless standards. The algorithmic optimizations employed to produce an FPGA friendly realization are discussed.     

Finite element modeling of low-velocity impact on laminated composite plates and cylindrical shells

In this study, composite laminates and shell structures subjected to low-velocity impact are investigated by numerical analysis using ABAQUS finite element code. In order to model the impact phenomena by commercial finite element codes, various procedures are available. Accurate modeling requires the appropriate selection of element type, solution method, impactor modeling method, meshing pattern and contact modeling. In this investigation, by considering several case studies with various conditions, validity of the existed modeling processes is examined. In each case, by comparing the results of various methods with the related available experimental test results in existing literature, the best procedure is proposed which can serve as benchmark method in low-velocity impact modeling of composite structures for future investigations.     

Peroxyl and hydroxyl radical scavenging activity of some natural phenolic antioxidants

The autoxidation of linoleic acid dispersed in an aqueous media and the antioxidant effect of hydroxytyrosol, oleuropein, caffeic acid and tyrosol were studied. Linoleic acid autoxidation rate was estimated by the increase of conjugated diene level and by the decrease of linoleic acid content in the samples. The phenolic compounds exhibited an antioxidant activity which increased in the order: tyrosol < caffeic acid < oleuropein < hydroxytyrosol. The analysis of the hydroperoxide isomers pointed out that hydroxytyrosol, oleuropein and caffeic acid at a concentration of 10⁻⁴M inhibited the formation oftrans- trans isomers in the increasing order: caffeic acid < oleuropein < hydroxytyrosol. This inhibition could be related to the ability of phenolic compounds to scavenge peroxyl radical. Tyrosol did not inhibit the formation oftranstrans isomers. Phenolic compounds were degraded as a consequence of their antioxidant activity and their degradation rate was positively correlated to their antioxidant efficacy. These phenolic compounds, at a concentration of 6 × 10⁻³M, also scavenged hydroxyl radical, with an efficiency which increased in the order: tyrosol < hydroxytyrosol < oleuropein < caffeic acid. Polar substituents at the para position, such as in caffeic acid and oleuropein, were correlated with higher hydroxyl radical quenching ability.